Tips
How to Unmold Flan Without the Caramel Sticking
By Fede5 min readUpdated
In short
To unmold flan without the caramel sticking, take it out of the fridge, set the mold in a bowl with boiling water around it for one minute, and run a knife around the edge if needed. The heat melts the caramel on the bottom, which hardened in the cold. Then put a plate on top, flip it, and tap the mold if it doesn't drop.
You made the caramel carefully, baked the flan in a water bath, waited all night, and when you flipped it, the caramel stayed stuck to the bottom of the mold, hard as a rock. I get it: it's one of the most frustrating things in the kitchen.
I have a tip I use every time, with all my flans, and it's really simple: one minute in boiling water before unmolding. Here's how to do it, why it works, and what to do earlier on, starting with the caramel, so your flan comes out whole.
Why does the caramel stick?
Caramel is sugar taken to a very high temperature. According to the sugar stages chart from the Exploratorium, San Francisco's science museum, at 160 °C (320 °F) it's a clear liquid with no water left, and around 170 °C (338 °F) it turns brown: that's caramel.
When you pour it into the mold and it cools, it hardens. Part of it softens later from the moisture in the flan, because sugar attracts water (it's hygroscopic, as Nigella Lawson's site explains), and turns into that runny sauce everyone loves. But the layer on the bottom, stuck to the metal and fridge-cold, usually stays hard. That's the part that won't come out.
The tip: one minute in boiling water
- Take the flan out of the fridge. Unmold it cold, only then.
- Set the mold in a bowl and pour boiling water around it, without letting any get inside.
- If needed, run a knife around the edge to loosen the flan from the sides.
- Leave it there for a minute. The heat from the water goes through the metal and melts the caramel on the bottom.
- Lift it out carefully. The mold is hot: use a kitchen towel. It happened to me while filming: I burned myself.
- Plate on top and flip, in one firm move.
- If it doesn't drop, tap it. Give the mold a few taps. In my video I had to tap it a whole bunch, but it came out, and the caramel came down with the flan.
The tip won't make the flan slide out on its own: what it does is make sure the caramel, now melted, pours out with the flan instead of staying stuck.
The caramel, from the start
A good unmolding starts with good caramel. Here's how I make it:
- Medium heat, sugar in the pan, and just enough water to moisten it. If you add too much water, no big deal: it just takes longer.
- Don't touch or stir it at first. Once it starts to take on color, then you can swirl the pan to even it out, since it's normal for some spots to darken first.
- Check the color on wet paper. In the pan, caramel looks darker than it really is. A drop on a damp piece of paper shows you the true color.
- Coat the mold well. Pour it in and, very carefully and with a kitchen towel, tilt the mold so the caramel runs up the sides.
If you want to know what happens to sugar as it turns into caramel, I explain it in what happens to sugar when it caramelizes.
A well-cooked flan unmolds better
The other secret is in the oven. My flans bake in a water bath at 180 °C (356 °F) for about 45 minutes. The water in the pan can't get hotter than boiling, as America's Test Kitchen explains: that way the flan cooks evenly, without overcooking at the edges.
Here's why that matters: an egg and milk custard sets at around 78-80 °C (172-176 °F), according to Belle Lowe's classic Experimental Cookery, and past about 89 °C (192 °F) it curdles and starts leaking liquid. An overcooked flan, says the Exploratorium, ends up full of little holes and oozing liquid.
After baking, let it cool and keep it in the fridge until you're ready to eat it.
| What happened | Why | What to do |
|---|---|---|
| The caramel stayed hard on the bottom | It hardened in the cold | One minute in boiling water before unmolding |
| The flan won't drop | It's stuck to the sides | A knife around the edge and a few taps |
| It broke coming out | Still warm or too soft | Chill it before unmolding |
| You burned your fingers | The mold comes out of boiling water | A kitchen towel, always |
The same trick for every flan
I use it the same way with condensed milk flan, the one shown here, with cream cheese flan, and with almond flan. It works for any flan with caramel on the bottom.
The recap: caramel spread all around, a water bath, the fridge, and right before serving, one minute in boiling water, a knife around the edge, and flip.
Frequently asked questions
How long should flan sit in hot water to unmold?
One minute in boiling water is enough to melt the caramel on the bottom of the mold.
Should you unmold flan cold or warm?
Cold: let it cool, keep it in the fridge, and unmold it right before serving using the boiling water trick.
Why does my flan have little holes?
Because it overcooked: above about 85-89 °C (185-192 °F) the custard curdles, leaks liquid, and fills with little holes. A water bath helps prevent it.
How can you tell the color of caramel?
Put a drop on a piece of wet paper: in the pan it looks darker than it is, and on the paper you see the true color.
Related recipes
Sources
The facts in this post come from these sources (checked when it was written).
- Cómo hacer flan de leche condensada — Fede Cocina (YouTube) (2021)
- Sugar Stages — Exploratorium
- Why were my forgotten cookies sticky? — Nigella Lawson (nigella.com) (2018)
- Why gentle heat guarantees smooth custards — America's Test Kitchen
- Experimental Cookery From the Chemical and Physical Standpoint: Custards — Belle Lowe (Iowa State College), en Chest of Books
- Science of Cooking: Gentle heat — Exploratorium



